Application

Malinly used for smelting cast lron, stainless steel, aoy stee, non-ferrous metals,including heavy metals (such as copper,lead) and preclous metals (such asgold, slver), etc. The equlpment is used in metallurgical industry, casting industry, non-metal smelting and other industrles

Steel shell

The open furace body includes: whirlwind dust removal envlronmental protection furace ld and titing fumace ol cylinder, Fumace lid lifting. newInductlon coll, energy saving yoke, full set of water inlet distrlbutor, imported carbonless hose and so on.

Adopting hydrauic tlting device. The furnace ls welded with high quallty steel structure, which is more safe, firm and durable; The sensor is enclosed by amagnetic yoke, cover area more than 65%. therefore,less magnetic fux leakage, high efficlency, save nearly 5% energy consumption than aluminum shelfurnace, Eaulpped with antl-leakage alarm devlce, can predict in advance to through the furnace.SOas to achleve the purpose of safe productlon. Meanwhlle,It can be equlpped wlth the furnace lining elector devlce.

The furnace lining ejector device consists of the following

1. Push out the oll cylinder.

2. Hydraullc valve and connecting plpe.

3. Furnace bottom jolnt matching the system.

The system operates as follows

Once the furnace lning cooling drops to 400'c, the furnace ls turned 90 degrees. Lift the ol cylinder wth a crane, conect the oll cylinder with the bottomof the furnace, start the hydraulic pump statlon and push out the furnace lining.

Products advantage

1. Good stablllty, low cost, smaller area occupled

2. Easy to operate, fast melting and low productlon cost.

3.Slmple structure, easy maintenance.

4. Can be dlrectly melted from the cold furnace, solutlon can be all empty, easy to replace the type of molten materlal.

5.Low nolse,qood workig environment.

6.Tallor-made according to the different melting metal.

7. induction coll of varlous speciftcations, reasonable selection of copper tube wall thickness and speclficatlons, so as to lmprove the utlzaton rate ofelectrlcal energy.

8.High performance insulatlon materlals are used.

9. The turn-to-turn gap of the inductlon coll is convenlent for malntenance and conductlve to the release of water vapor.

Smoke collecting device can be used to improve working envlronment.

Power supply

This melting furnace can realze fully automatlc remote control,lncluding PLC programmable controller, HMl man-machine interface or lindustrlal controlcomputer system.industrlal control confquration software and varlous sensors, it can realze automatc operaton, such as automatlc constant temperatureautomatic oven and furnace leakage alarm, which ls safer and more convenlent to use.

The power advantage

1. Through a single power supply device, reallze the mass productlon capacity of multlple furnaces.

2. Uninterruptlble melting and accurate thermal insulatlon or overheat temperature control.

3. lt can preheat, sintering, melting and ultra-low power insulatlon for multlple electric furnaces at the same time.

4. Each furnace adopts independent control system.

5. Can provlde full constant power to one furnace whlle lsolating the other under maintenance.

6. Just one set of power connectlon and water connectlon, greatly reduclng installatton, operatlon and malntenance costs7. The latest generatlon of digltal operatlon technology, Single Cllp Microcomputer program control.

8. Lower starting frequency, ultra-low power oven.

9. Full open rectifler, high power factor, Higher harmonics are small.

10.The equlpment power utlllzatlon rate ls close to 100%

11. Liquld metal is more productive and does not need to increase electricity demand.

12. lt can produce efficlently and match different metal llquld demand levels.

3. Optical fiber transmisslon trigger signal, electronic control using dlgital mode.

4.Very competltlve power consumptlon indicator.

15. Comply with domestlc and internatlonal electrical safety deslgn standards.

16. More perfect and intelllgent protectlon functlon.